Facts about Cooling Tower Level Control - Kooldrop

Facts about Cooling Tower Level Control - Kooldrop


A Cooling Tower is a device that extracts heat from the process waste and releases it to the atmosphere. The towers used in cooling work with two methods to remove heat: evaporation and air. In the first process, the towers vaporize the water level of the Cooling tower to dissipate heat and cool the working fluid to near humid air temperature. In the second case, the cooling tower's level control for cooling the working fluid relies entirely on air and only occurs with closed loop cooling towers. As heat and water breakout the towers through evaporation so some additional water must be periodically added to the system. At this point, the need for a water level controller emerges.

A Water Level Controller is a device that is used to manage water levels on a variety of systems such as water tanks, swimming pools and pumps. Its basic function encompasses of regulating water flow and optimizing system performance. Although cooling tower water level management is one of the most complex aspects of cooling tower level control, it can be easily controlled and monitored with the current building automation system. However, without the best control of the level, it is impossible to achieve satisfactory results in terms of water management. The first priority of such a program is a reliable system cycle. It is best to measure the conductivity of the water.

Functions of Cooling Tower Water Level Controller:

A flush valve must be activated at a prepared location to drain water into the sewage system. The subsequent introduction of the low conductivity make-up water is continued until the conductivity value falls below the set point. For this function, automatic units are used under the chords of the manufacturer. Cooling tower water level management uses NCD equipment or no chemical equipment. The units are used to control corrosion, deposits, deposits, biological growth and other adverse effects and have no negative impact on the environment. The various processes implemented in the cooling towers are electrostatic, magnetic, electromagnetically induced, power pulses, hydrodynamic zeta potential, and ionization. Several studies have shown that these control elements for the levels have no practical use in the water treatment process.

The water level controllers may look like the competition but the unit is revolutionary in its design. The water level control series is perfect in any application where water level management is required or important such as “cooling tower basins”, “water holding tanks for cooling towers”, “cooling tower sumps” and “evaporative condensers”. These revolutionary level control systems use a microprocessor that ensures correct operation by monitoring all sensor probes and then gives the corresponding outputs that ultimately drives the power relays, the Building Automation System and a visual indication of the operational status. It also ensures user-friendly operation by using the Modular Construction and a self-test feature. Moreover, the devices include the water level control sensor, the WaterLine Control panel and the mounting assembly for the sensor.

An unbiased review of gadget literature has shown that their operations are not based on scientifically accepted principles, but their performance is essentially acceptable. Water level maintenance requires the support of some state of the art, state-of-the-art laboratory-equipped equipment. Well-managed and experienced treatments, however, may also be subject to significant problems and failures due to changing conditions. Therefore, the backup support of an experienced team of experts is requested to make the process successful.

In addition, the quality of the chemical products used and the type of control equipment for the cooling tower levels determine the effectiveness of the process. While the entire process is subject to sedimentation, corrosion, biological contamination, and sedimentation, operating costs have also increased. The process also tends to be shut down by equipment replacement, pathological organism, etc. Apart from that, the increased energy and water consumption has made the process extremely exorbitant in terms of both money and resources.

Best Cooling Tower Manufacturers:

If you are looking for water level controls for cooling towers, Cooling Tower Manufacturer can help as they manufacture state-of-the-art water level control systems that provide automatic water level control in cooling towers, remote sump tanks, evaporative condensers, and closed-circuit liquid coolers. The stainless steel cooling tower level sensors or probes measure the water level in every cooling tower basin or sump of any size. The electronic level controllers replace BAC, EVAPCO and Marley Cooling Tower directly.

The KOOL DROP Cooling Tower is the best FRP Cooling Tower manufacturer in India. The people with us manufacture round and square shaped FRP cooling towers based on forced draft / induced draft counter flow design. The KOOL DROP Cooling Tower also manufactures WOOD cooling towers based on the induced draft Crossflow design. In a short time, KOOL DROP has created a niche and has become one of the most popular brands of cooling towers in India.

Facts about Cooling Tower Level Control - Kooldrop


A Read More

Difference between cooling tower and condenser

A Cooling Tower is a heat exchanger ...

Read More

Are you confused among cooling tower Manufacturers? Here is the way out

The function of a Read More

Cooling Tower Material and its Main Components

Cooling Towers are an essential feature for many industries as it helps to reject excessive heat....

Read More

Cooling Tower Terminology

A Cooling Tower is a heat rejection device that transfers heat fr...

Read More

Difference between Natural Draft and Forced Draft Cooling Towers

Due to continuous mechanical processes, industrial processes and machinery generate huge amounts ...

Read More

10 Most important Characteristics of Cooling Tower Water Treatment

A cooling tower water system is the process of separating heat from hot water and then ejecting t...

Read More

Fundamental Principles of Cooling Towers

Cooling towers are heat exchanger units to expos...

Read More

How we choose best Cooling tower manufacturers

A Cooling Tower is the best mechanism to treat your equipment and save water. Pe...

Read More

Types of Wood used in Wooden Cooling Towers

Wooden cooling towers have been an old construction mechanism but over the period of time due to ...

Read More

Improving Energy Efficiency of Cooling Towers


Improving Energy Efficiency o...

Read More

Types of cooling towers


Understanding the Different Types of Cooli...

Read More

The Process of Cooling Tower Water Treatment System

Industrial companies often use a cooling tower to facilitate proper functioning ...

Read More

How Cooling Towers Work

A Cooling Tower is a heat exchanger device meant specifically for cooling down m...

Read More

What is the Purpose of fill in a Cooling Tower?

The Cooling Tower contains fills as the main com...

Read More

What is the difference between a Chiller and a Cooling Tower?

If you’re going to buy a cooling system for your company and co...

Read More

Our Clients

Copyright © 2018 Kooldrop - All Rights Reserved.